Call Today

 

This post following next in relation to Installing A Bathtub is highly compelling. You should check this stuff out.

Setting up a bath tub isn't precisely rocket science, however it does need strong plumbing, carpentry, as well as often, tiling skills. Replacing an old bath tub with a new one is also a reasonably hard job. If the old tub is readily obtainable, the job can relocate immediately; if you need to open a wall surface to eliminate the old tub and also place the new tub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will certainly require a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have actually qualified yourself for the work and also fit trying it. Instead of hiring a contractor to take over a halfway-completed task, it is far better to consider using one before you begin. Chances are you may need a specialist plumber to make tube connections.
This write-up will certainly assist you set up a new tub in your restroom if you have actually currently acquired a new bathtub and do not need to alter the arrangement of your previous water supply pipelines.
Your devices as well as product checklist ought to make up the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Measuring tape


• Pipeline Caps


 

Removing Old Taps

If you require to change old faucets with new ones as a part of your installation, then the first thing you should do is separate the water supply. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The procedure of eliminating the existing faucets can be rather problematic because of the restricted accessibility that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a towel prepared for the remaining water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning during this process. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Before going on to fit the new taps, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.

 

 

Suitable New Touches

If the tails of the brand-new taps are plastic, then you will certainly require a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end offers a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washers are in place in between the tap and also the sink. Secure the faucet in position with the producer given backnut. When the faucet is securely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The previous kind needs to be linked to the tap ends initially, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

 

 

Installing the Bathtub

Utilizing both wood boards under its feet, place the tub in the needed position. The wood boards are handy in uniformly spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto 4 small points.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the bathtub up until the level reviews level.
To set up faucets, fit all-time low of the furthest versatile faucet port to the proper supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the water system as well as inspect all joints and brand-new pipework for leaks and also tighten them if essential. Fill up the bathtub as well as additionally examine the overflow outlet and the typical electrical outlet for leaks.
Ultimately, fix the bath paneling as explained in the maker's instruction manual. Tiling as well as securing around the tub ought to wait till the bath tub has actually been utilized at the very least when as this will certainly settle it right into its final setting.

 

 

Planning for the Setup

To start with, the supporting framework supplied with the bath should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to ensure that if the tap includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets system to stop pressure on the bathtub.
Fit the flexible faucet ports to the bottom of the two taps making use of 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its last placement.

 

 

Tiling Around the Tub

In the area where the bath satisfies the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to split an inflexible seal, creating the water to pass through the wall surface between the bath and the tiling, leading to problems with moisture and possible leakages to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, as well as can sealing spaces up to a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water prior to sealing, to allow for the activity experienced when the bathtub is in usage. The sealant can break fairly early if you do not consider this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily readily available on the market. It is suggested to fit the tiles utilizing waterproof or waterproof sticky and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you really like reading up on How to Install a Bathtub Yourself? Try leaving a remark down the page. We'd be pleased to hear your feelings about this write up. We hope that you visit us again in the near future. Sharing is good. You won't know, you will be doing someone a favor. We truly appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.

Pro help? Call now!